NEW ADDRESS!
11812 Main Street Suite C104
Fredericksburg, VA 22408

TOLL-FREE
1-866-IRON-PIG

LOCAL
(540) 361-7400

TECH SUPPORT
Info

ROCK SLIDERS

---

 

 

Tired of tearing up cheap poly flares? Time for a set of IPOR's new indestructable fender flares!

• Made from formed 1/8" plate steel these flares are suitable for pounding on trees and rocks.
• The 1/4" back plane can be drilled & tapped for a no-weld installation.
• Cut-out maximizes body protection and tire clearance. (shown here with a 37" IROK)
• Sold in pairs, one left side and one right side

Limited time only - $349.95

 

---

 

FJ80 ROCK SLIDERS

Iron Pig Off Road is pleased to offer high quality Metal Tech Rock Sliders for your 80 series:

 

 

~ 100% Precision Laser Cut and Formed Steel
~ 2 Stage Rub Rail
~ Powder Coated Inside and Out
~ Bolt-on
~ Accessory Mounts

The CAD developed sliders are built on an “aircraft wing” type of construction. The outer “skin” or shell is precision laser cut 3/16” steel and formed on CNC forming equipment. On the inside a combination of ¼” and 3/16” inner ribs support the outer shell. This produces and extremely rigid, relatively light weight main body for the slider. The forming of the slider shell also allows for it to flow with the rounded lines of the 80.

 

The CAT GUARD is precision laser cut and formed from one solid ½” thick steel plate. The guard acts as a large ski to protect the expensive catalectic converter and not hinder forward motion off road. The guard allows the most air movement of any other design and will not collect trail debris. The main thing is allowing maximum air movement to allow heat to be bled off; excessive heat will destroy a cat.

 

 

Maximum performance: The sliders do more than protect your truck!

Bolt on a 2.5-gallon air tank or mount up a spare Optima battery all tucked up under your truck.
For night off road travel use the four rock light tabs all pre-installed ready to go. Since the slider is a wing design you can route all the wiring cleanly inside the slider!
The right side slider has an accessory mount built into it to capitalize on the large open cavity under the right side floor just outside of the frame rail. By using the optional accessory mount/skid plate you bolt the mount directly to your sliders and frame. The mount holds either a 2.5gl air tank or a spare Optima battery. The mounting plate is laser cut and formed out of ¼ inch plate and acts as a skid guard for what is mounted above it. All this is tucked up above the main body of the sliders.

Rub rail: The outside of the slider has a two-stage rub rail. The aft portion of the rub rail is 1.5” further outward that the front half. This area of the slider will push the back end of your truck away from the obstacle you are traversing (This helps save your ¼ panel)!

 

$899.95 for the 93-94 FZJ-80

$899.95 for the 95-97 FZJ-80 and 450LX

 

Note: Beware competitors offering a lesser product for a cheaper price. Cheap sliders fold up and don't offer the protection you're looking for. We've selected MT sliders because of their intensive R&D and innovative design. You've chosen to drive the most capable truck on the market, be sure to protect it with the best quality products as well.

---

FJ55 ROCKER PANELS

Includes only stamped steel outer rocker section. Custom installation with additional options shown below. Please call for details.

Price: $190/pair

 

©1999-2007 Iron Pig Off Road. All rights reserved. | Web design by Idea Shop

Land Cruiser is a registered trademark of Toyota Motor Corporation.
This site is in no way affiliated with or endorsed by Toyota Motor Corporation
or its subsidiaries. Please read our disclaimer.